How to Calibrate a Click Wrench

“Click” “type wrenches are the most widely used torque product in the world. When the set torque is reached, a click wrench typically emits an audible “click” and a slight moment of release of up to three degrees, before going positive. After the “click”, an operator should stop pulling as torque is achieved and the tool becomes positive. If not, the assembler will over torque the fastener. Even a couple extra pulls on the handle is not good. Proper use and training is required so that operators stop pulling the moment the click sound is heard or felt to prevent the fastener being over tightened.

A torque wrench is a precision tool and should be treated and maintained like a measuring instrument.  A torque wrench must be properly calibrated and maintained on a regular preventative maintenance and calibration schedule.

When calibrating a click wrench it is recommended following the ISO6789 International Standard requirements. The standard covers items such as calibration methods, design requirements, and tool types. For calibrating a torque wrench, either use a torque tester or torque  sensor within the range of the torque wrench.

Torque Calibration Process for a Click Wrench

  • To begin, you must pre-load the torque wrench 5 times to the tool’s maximum torque capacity without taking a torque measurement. Make sure to use a calibration device that is within the proper range.
  • Next set your click wrench at 20% of the torque range, and record a total of 5 torque readings.
  • Next adjust your click wrench to 60% of torque range, and again record 5 readings.
  • Complete final 5 torque readings with the click wrench set to 100% of the maximum torque range capacity.
  • Check that all readings are within the allowable tolerance. If they are outside the accuracy limit, then adjust the wrench in accordance to the manufacturer’s instructions. Repeat torque calibration process until all torque values are acceptable.
  • Now your click wrench is ready for use. It is recommended to check calibration every 5,000 cycles to ensure the best performance.

After being used, adjustable click wrenches should be turned back to the minimum scale value. This helps to preserve the spring and ensures a longer product life cycle with high precision and maintain the best accuracy.

Some manufacturing companies own torque calibration equipment and calibrate their tools “in-house”,  while other companies send their tools out to a calibration lab. Be selective when choosing a lab. A facility needs to comply with quality standards. A lab that is ISO 9001 certified and ISO 17025 accredited is a good starting point.

Mountz Inc. features an experienced calibration and repair staff. Our trained technicians can calibrate and repair most any tool. Mountz provides rapid service with quality that you can trust as we offer two state-of-the-art calibration lab and repair facilities that can calibrate up to 20,000 foot-pounds.

Since 1965, Mountz’s in-depth knowledge of torque is reflected in our tool’s craftsmanship and our ability to provide solutions to both common and uncommon torque applications. We perform calibrations in accordance with ANSI/NCSL-Z540. Mountz is dedicated solely to the manufacturing, marketing and servicing of high quality torque tools.

Using a quality torque wrench makes a safer world through accuracy and precision. Controlling torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures. Fasteners that are insufficiently fastened can vibrate loose and excessive torque can strip threaded fasteners.

If you need your wrench or other torque tools calibrated or repaired, contact the Mountz service staff. For further technical questions, ask the torque experts.

Mountz Receives Wonderlic Leadership Award

Wonderlic Award for Mountz

Mountz, Inc. earns award from the Wonderlic Leadership Invitational 2013. Wonderlic, the nation’s leading publisher of employment assessments and student admissions tests, recently announced the “Most Engaging” Leaders and Employers in the Wonderlic Leadership Invitational.

The purpose of the invitational was to help organizations evaluate the quality of their leadership team. A leader is more than a job title or position of authority. Excellent leaders create an environment where others want to follow by inspiring others to internalize organizational goals and values, apply extraordinary effort, and achieve results above and beyond expectations.

The Invitational was open to organizations of all sizes as well as individuals. Leaders and their direct reports completed a series of questionnaires, which produced a Favorability Engagement Rating that was used to determine the most engaging leaders and organizations. Wonderlic recently announced that Mountz Inc. is one of the top ten organizations.

“It’s no secret that leaders play a pivotal role in the success of an organization,” states Michael Callans, Vice President of Research and Development at Wonderlic. “Everyone who entered showed a strong interest in discovering where they excelled and where they needed improvement in order to help maintain and develop their leadership style.” Continue reading Mountz Receives Wonderlic Leadership Award

Meet the President & CEO of Mountz, Inc.

Since 1965, Mountz Inc. has proven its in-depth knowledge of torque by consistently developing, producing, marketing and servicing highly sophisticated, cutting-edge torque tools. Making a safer world through accuracy and precision is the core purpose Mountz, Inc. Brad Mountz, President & CEO, has been with company for 30 years and believes that one of the objectives for the company is to produce and supply the highest quality products and services that improves the quality, reliability and safety of our customers’ product.

The value of service is at the forefront of Mountz, Inc. Caring and cherishing the needs of the customer is a priority at Mountz. Providing a solution and helping a customer solve a problem is vital. With every customer interaction, Mountz strives to exceed the customer’s expectation.

“To give real service you must add something which cannot be bought or measured with money, and that is sincerity and integrity.” – Douglas Adams (Author). Continue reading Meet the President & CEO of Mountz, Inc.

New Online Virtual Car Show – “At the Track”

New Online Virtual Car Show

MountzPro® launches “At the Track“, a new daily “car show” blog. The new online virtual car show allows all car enthusiasts to share and display pictures of their car and how they’ve modified their ride. It’s a show for classic cars, muscle cars, exotic cars, supercars, trucks, motorcycles and everyday cars, all in one.

MountzPro invites all car enthusiasts to submit pictures of their “ride”.  Once an enthusiast submits a photograph and written description, he or she competes in a quarterly “Best in Show” contest for a cash prize. Readers can  vote for “Best in Show” and post comments on individual cars. Enthusiasts think they have the best looking car on the block, but how does it match up against the rest of the world? They can share their ride and see how the community votes and express their opinions.

MountzPro, a new division of the nearly 50-year-old Mountz, Inc., focuses exclusively on the automotive professionals market. MountzPro has recently introduced an innovative automotive torque wrench designed to address the shortcomings associated with the typical torque wrench. Continue reading New Online Virtual Car Show – “At the Track”

Detect and Prevent Fastening Errors

BLG-BC1

Counting screws is not the new song title from the rock band “Counting Crows.” Screw counting is a quality control process utilized in the manufacturing environment. Tightening hundreds and hundreds fasteners daily, assembly operators can forget to fasten some screws here or there during the monotonous routine. For complex fastening regimes with multiple screws on fast moving assembly lines, often fasteners may not always be installed and seated properly. These are common symptoms that plague many manufactures. How to get it right the first time?

The goal of the screw counting process is to ensure that all fasteners are accounted for during the assembly process. Further a fastening error is identified on the assembly line, the more it costs in rework time and expenses. If a fastening error is committed and detected during the assembly process, the operator can correct it or prevent the faulty product from moving along the manufacturing line or being shipped out to a customer.

A screw counter helps manufacturers detect and eliminate costly screw-fastening errors during the assembly process. Using a screw counter is like putting the eyes and ears of a quality control manager where they are needed most – right in the assembly area.

The new BLG-BC1 Series by Mountz, Inc. is an unique electric screwdriver, as it features a built-in screw counter. Whereas most screw counting systems require an external device be connected to the electric torque screwdriver. The BLG-BC1 doesn’t. This power tool verifies that all fasteners have been installed and seated properly. Continue reading Detect and Prevent Fastening Errors

Remote Power

Torque Multiplier

Pipelines that stretch across miles and miles of vast open, remote land transporting liquids and gases require maintenance. Deep below the surface in an underground mining operation, large industrial vehicles or tools require routine maintenance. The large bolts used to securely join sections of pipes and valves together or used with mining vehicles require torque control and power to tightening and untightening these bolts.

Access to power for these locations might not be easily accessible like a power outlet at your home or an air compressor inside a maintenance shop. Remote power is needed. Power for remote locations. A hand torque multiplier is the torque solution. No electricity or air is required to operate the tool. Only the hand multiplier and a torque wrench are needed for the maintenance technician to loosen and retighten threaded fasteners, nuts or bolts.

The gearing design of a manual torque multiplier allows for high torque output with minimal input from an operator. A torque wrench is placed into the input drive end of the torque multiplier. A socket and reaction device are used on the other end where the square drive is located. These hand tools feature a torque multiplication ratio, which is different for each tool model and brand. The technician pulls the torque wrench and applies force. The torque output is multiplied by the hand multiplier tool. Requiring less effort and strain for the technician.

Benefits of Manual Torque Multipliers

  • Allows for high torque output with minimal input from an operator
  • Perfect for applications where air and electricity aren’t accessible
  • Precision tightening & loosening of all heavy duty fastening connections
  • Replacement for impact spanners, pipe extensions and other insufficient bolting methods

The HG hand torque multipliers offered by Mountz are engineered for enduring performance. Mountz offers various hand torque multiplier models with a maximum torque capacity up to 36,800 foot-pounds, satisfying the requirements of even the most demanding MRO applications.

The hand torque multiplier is the ideal tool for dealing with difficult nuts and bolts – those requiring extreme applications of torque for loosening or tightening. This compact, versatile HG torque multiplier applies precise amounts of torque or power in nearly all heavy-duty fastening situations, eliminating the requirements for multiple operators, and enhancing safety as well.

During the routine maintenance process of their aircraft, a helicopter manufacturer had a critical torque application. The rotor of the helicopter required servicing after every 20 hours of flight. Loosening and retightening the rotor assembly nut during the maintenance process of the helicopter’s rotor required power – remote power. Some of these aircraft are serviced in very remote locations, where air or power is not readily available or reliable. Ensuring proper torque control is achieved for the rotor assembly nut is a critical element for maintaining the continuous safe operation of their helicopter. The director of maintenance selected the Mountz hand torque multiplier as the only option to resolve their critical maintenance application issue.

From tightening large industrial bolts used in windmill gearbox assemblies to bolting maintenance applications for oil & gas pipelines, the Mountz hand torque multiplier achieves precision torque in a cost-efficient manner. Only Mountz torque multipliers provide precision torque control, making it easier and often safer to assemble and service-threaded fasteners while reducing application problems and tool costs.

Using a quality torque multiplier makes a safer world through accuracy and precision. Controlling torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised. The failure of a five-dollar bolt that isn’t properly tightened can lead to catastrophic or latent failures. Fasteners that are insufficiently fastened can vibrate loose and excessive torque can strip threaded fasteners.

Contact us with any questions you may have. We can help you make the proper choice, every time.

Prevent the Risk of Injuries and Additional Expenses with an Ergonomic Solution

articulated torque arm

A power tool incidentally dropped by an assembly operator at a workstation, causes additional expenses and reduces productivity. Repairing and replacing parts for the assembly tool, recalibrating the tool after its been dropped or purchasing a new replacement tool are all additional, unnecessary costs.

Daily, weekly, monthly, an assembly operator performs hundreds and thousands of repetitive fastening  rundowns. If the assembly area lacks any ergonomic devices for the operator to use, it provides the opportunity for additional expenses to incur. You don’t have to play tennis to get “Tennis elbow.” Injuries caused by repetitive work and overusing the arm can occur in leisurely or daily work activities. Workers’ compensation claims are costly. Litigation expenses can quickly skyrocket.

These additional costs are preventable. When budgeting or purchasing a power tool for an assembly station, an ergonomic torque arm shouldn’t be viewed as an additional cost. It’s a preventive expense. A necessary action to prevent additional risks and costs from incurring in the near future. No one wants to be responsible for an injury occurring to a fellow co-worker.

There are many ergonomic solutions available for assembly-line workers today. Torque arms are available in various options and configurations, allowing you to select a solution that is well suited for your fastening application and workstation configuration. The EZ-Glider articulated torque arm offered by Mountz is one potential ergonomic solution to consider. Continue reading Prevent the Risk of Injuries and Additional Expenses with an Ergonomic Solution

Reduce the Risk of Over & Under Tightening with a Break-Over Torque Wrench

MTBN Break-Over Torque Wrench

In selecting a torque wrench, you need to know the torque required for the fastening application. In general, that seems like common sense. How can you ensure the proper torque is being applied while tightening a fastener or bolt with a torque wrench? By selecting the proper wrench for the assembly application, which can be a little confusing and stressful if not properly trained.

There are a wide variety of preset and adjustable torque wrench options to select. Educating yourself on the different torque delivery mechanisms offered for wrenches is worth learning. With mechanical torque wrenches, there three general types: cam-over torque wrenches, break-over torque wrenches and click wrenches. Each of the three wrench styles has a specific purpose and utility.

Click wrenches typically break at 3 degrees after the preset torque is reached and then the tool becomes positive. Thus, easily allowing for an operator to incidentally apply more force and over torque the fastener. Or intentionally apply more force because of the operator’s mindset is that “more force is good”.

A cam-over wrench removes the operator’s influence from the application as the tool prevents a fastener or bolt from being under and over tightened.  As a quality control tool, the wrench allows any user to deliver the correct torque with confidence regardless of task and operator skill level.

Break-over wrenches improve control of the fastening process by reducing the risk of both over and under tightening. Upon reaching the preset torque value, the tool “breaks” at a specific point along the tool’s shaft – usually at a pivot point near the tool’s head. The unique break-over mechanism, provides an operator ample time to react once the target torque is reached and to stop applying any additional force to the fastener. Continue reading Reduce the Risk of Over & Under Tightening with a Break-Over Torque Wrench

Tool Balancers Provide Easy Handling and Comfort

Tool Balancers

In a manufacturing workstation, having a clean, organized and ergonomic work area enhances productivity and improves the assembly time and process. Safety at the workstation is a key aspect that managers need to review on a continuous ongoing basis. Exposure to high forces, awkward postures, lifting, and repetition are some common activities that can performed by an employee at assembly workstation, which can lead to potential injuries and an increase of costly compensation claims.

Risk of injury for the assembly operator depends on the duration, frequency or intensity of exposure to the assembly job function. Assembly operators often spend long periods standing and/or performing repetitive motions and lifting over the course of their shift. Ergonomic solutions can considerably reduce the physical impact of these daily industrial tasks. Assembling mechanical and electronic components demands efficiency, space, productivity and ergonomics.

Manufacturing managers need to get the tools necessary to create a cost-effective, comprehensive, and strategic solution to ensure the workplace functions with health and safety as a key priority. Torque arms are one ergonomic solution available for the assembly area. Another solution are tool balancers, which provide easy handling for operators that work with tools for long, continuous hours. The ergonomic balancers allow tools to be positioned over the work station for comfortable operation and can be used with pneumatic, electric, hydraulic or other tools.

Best practices for improving the safety at an assembly workstation:

  • Make ergonomic efforts a priority.
  • Conduct routine meetings between employees and supervisors to discuss ergonomic concerns and solutions.
  • Set ergonomic goals and track results. Share results with the employees.
  • Train employees to be more aware of ergonomic risk factors.
  • Bring in outside experts for consultations, if needed.
  • Promote employee involvement with the efforts to improve workplace conditions.

The outside-expert point deserves emphasis. Ergonomic consulting firms now service clients well beyond traditional manufacturing. No verification casinos running 24-hour support floors, logistics dispatch centers, and pharmaceutical packaging operations all face the same repetitive-motion and prolonged-standing risks. The assessment frameworks these consultants bring back from those environments often introduce solutions that assembly managers would not have considered on their own.

A tool balancer not only helps improve safety, but also protects an assembly tool from accidentally damage like being knocked off a workbench. Damaged assembly tools increase cost and cause production delays. Once a tool is dropped on the floor, it’s recommended to pull the tool from the production line and have it sent in for a service evaluation. The impact may damage internal parts, which may be unseen from the exterior viewpoint. Also, the torque setting needs to be evaluated as the tool may need to be recalibrated.

Mountz offers an assortment of ergonomic tool balancers for various applications:
Zero Gravity Tool Balancers (weight capacity ranges of 1.1-264 lbs)
Designed to provide gravity defying – “true balance”. These models are compact and durable. Wide range of models that can handle small tools and larger, heavier tools.

Retractor Tool Balancers (weight capacity ranges of 1.1-11 lbs)
This style balancer is the most commonly used balancer. The tension of the balancer can easily be adjusted by hand with the adjustment knob on the side.

Hose Reel Tool Balancers (weight capacity ranges of 1.1-11 lbs)
Durable Hose Reel balancers are designed for small pneumatic tools. Integrating the air hose and support cable keeps the work area clean.

Tool Positioner Balancers (weight capacity ranges of  1 -12 lbs)
A small, lightweight tool positioner that allows tools to be positioned over a work area for comfortable operation.

When planning a production area, it pays dividends for manufacturers in the long term to plan the ergonomics of the operation and consult a health and safety inspector or ergonomic manager. Ensuring both the workplace and the assembly operation are compatible with the majority of operators that handle the assembly tools, reduces future costs arising from work-related health disorders among operators, along with costs arising from poor product quality.

Using an ergonomic tool balancer makes a safer world through accuracy and precision.

Request a quote for tool balancer.

Preset Torque Screwdrivers

Preset Torque Screwdriver

A preset torque screwdriver is similar to a person setting an alarm clock to signal the achievement of a selected time. The torque screwdriver is pre-set to the required torque value of the application and then the tool signals the operator when torque is achieved. A preset torque screwdriver does not feature an external adjustment scale. These tools have internal adjustment mechanism for setting the torque value and must be preset using a torque tester. Preset screwdrivers are ideal for production applications where there is one torque setting required and you need to prevent incidental or operator tampering of the torque setting. However, if the torque specification changes or new project requires a different torque setting, the preset torque screwdriver is still flexible enough that a new torque setting can be set internally using a torque analyzer.

The cam-over philosophy of each Mountz hand torque screwdriver prevents a fastener or bolt from being under and over tightened. These torque tools are ideal for production applications where over-torque conditions are not tolerated. As a quality control tool, the torque screwdriver allows any user to deliver the correct torque with confidence regardless of task and operator skill level.

The design action of the cam-over torque screwdriver is such that when the tool reaches its preset torque value the mechanism disengages from the drive thus limiting the torque applied. Also, the thrust bearings insure that the torque setting is independent of any end load applied by the operator. Designed for variety of industries like medical, aerospace, semiconductor, electronics, and communications, a Mountz preset torque screwdriver ensures proper torque control. Featuring a tamper-proof internal adjustment, the Mountz preset torque screwdrivers have no external adjustment scale and must be pre-set using a torque tester. Continue reading Preset Torque Screwdrivers